It's all about the Software

SDR Console currently only supports control of external radio using Omni-Rig. While Omni-Rig is a great package it has some serious downsides.

The root problem is that it is very difficult to make Omni-Rig co-exist with other radio control...

I would like to ask if it is possible, and if not already present in the software, to add a second sound card for each single receiver. For example, for digital modes,
I could mute the audio output from the headphones/speakers, but at the same time...

I've put a small SDR console remote control project on hold due to some bugs in the TS-2000's RS232 remote control protocol (as well as some other limitations that prevent interaction with certain features).

I had considered trying to combine the...

I'm very confused why binaural is available for AM and SAM, but not DSB.

SAM-Binaural makes sense in phase-locking the (virtual) CIO to the *strongest* carrier.
An unlocked DSB-Binaural alternative would be useful for resolving stations with...

Hello Simon, et. al.,

I'd like to offer my encouragement and perhaps other to further the development of a G2 Radio Definition for SDR Console. It seems more development is coming from Apache Labs along similar lines...G1 and the ANAN-G2-1K 1000W....

Utilizing server functionality, I have already set up a remote server to observe signal propagation across various bands at any time. It would be greatly convenient if I could view the received signal stream on the remote server using an Android app...

I would like to request that the ability to switch from internal clock to external clock ( ck1 ) be added. Probably under the radio options tab. As an EME operator, I need an exact frequency reference. It seems that the feature is available in the...

Hello.
Many modern communication systems use unique ACF (autocorrelation) values, so this algorithm would be very useful for rapid system identification. It is also very useful for viewing the PRF of OTHRs.

If this request is accepted and included...

Hi all.

The CROP tool in the Data file analyzer shows the parameters of the selected area.
Perhaps you can ad a control to export those data to the Data File Editor and open it for fine tuning and processing the selected area.

data-export.jpg...

Today we have the original Pluto Rev C or later plus various Pluto clones. They all support at least 2 RX and TX antennas. Would it be possible in a future release of SDR Console to select which antenna pair you want to use?

Thanks
Johan ZS6JPL

Is it possible ( pretty please) to add the facility to cycle through the filters with a MIDI device as defined in the current mode selection?

As I posted on the IO forum, I find the incremental change of 50hz much too low when in BFM mode.. what...

Hi Simon,
Using Console 3.3. When using QO-100, I would find it very helpul if the Rx audio could be muted automatically when the Tx button is pressed. This would make for a much quicker change-over. Perhaps you could incorporate a tick box 'Auto...

Greetings.

Can I make another suggestion re: MIDI?

Can the Data Playback functions be added to the possible commands that can be mapped to MIDI?
Would only need to be the START, STOP, PAUSE, BACK/FORWARD (by x interval as previously set).

Being...

Dear Simon,

to build a full radio with pluto (may be on a raspberry...) the only feature we need is the ability to move RIT via MIDI command.
It is necessary, for example, on the QO-100 where the correspondent is not always isofrequency and SDR...

I got a new laptop that runs Windows 11. However, the key that was the right Ctrl key is now the CoPilot key. I find this very annoying. I want the Ctrl key back.

The result of Googling on this issue results in the suggestion of installing...

Would it be possible to add support for 2MS/s transmissions (repeater outputs) please?

very best regards,

Justin - G8YTZ

Hi All,
I have a request regarding CAT command to select a specific Receiver RX1,RX2,etc...
With FA command I able to set frequency *FA, FB,FC, etc ) but I can't enable a specific receiver.

I only see in MIDI configuration the possibility to select...

Hi ,

is there anything going on for the Red Pitaya 16 bit ?

Kind Regards

Pat

As posted to the IO group a little while back, but putting it here in case it gets lost....

I have used the Memories a lot more recently, for example to put beacon frequencies in, or for using as a scratchpad during openings.

I find it's better...

Hello,
in the following groups.io discussion it was already asked about flip mode implementation for better rotor control.

I now wanted to put this feature request in the correct location.

The gist is as follows.

For rotors supporting 180° of...

how about feature that at the click of a button a text or xml file so that the whole configuration is easily attached to a post.

Thank you for reading this.

Amongst other thing, I use the software as panadapter, synched with my HF rig. The system works like a charm, but I find it annoying that any time I change band on the RTX, the amount of spectrum I see on the panadapter...

I just changed from ICOM 7300 to ICOM7610. On the 7300, I use a IF tapping card to get the signal to a RSP1B SDR, itself piloted by SDR Console and it works so well. On the 7610, I was hoping to use the IQ signal from ICOM that work with HDSDR but...

Hi,

to my knowledge the actual Aaronia support is limited to the v6 full version , not the ECO. So I wonder if it is planned to support also the ECO, as this is for sure the radio that will be bought by many hobbyists.

I own the ECO in RX/TX...

With regard to the Frequency Database feature, it would be nice, due to my aforementioned laziness, that it might somehow highlight broadcasts that should be on now based on the current time so as to not have to sift through a sometimes long list....