It's all about the Software

I think this is very easy to add this feature. Make the frequency of a spot in the DX cluster clickable. When clicking, it will change the frequency of the SDR play to the frequency of the spot.

Now we are at this feature, why not add a link on...

As if Simon isn't busy enough, here is something that is a game changer.

Check out this 32 second clip.

This would be great in any sdr console.

Hi

A feature i'll appreciate a lot is a scanner.

Hello Simon
Concerns video recording
I am under the version: SDR-Radio V3.0.26, 64-bit, 2020-10-07_1518.
As with standard Audio recordings, you can also highlight the presence of the recording because currently no recording information is displayed...

Been putting my RX-888 through its paces on the UHF bands over the past couple of weeks, & have noticed that I can get better performance out of it using HDSDR with the RX-888 ExtIO DLL (the one with the COMING SOON graphic when it loads). The...

I have my tuning step size for ssb set to 10hz. When I am on a crowded band, I will start from the left and tune the first signal in. Then to browse the band I will point the mouse cursor to the 1khz digit and scroll with the mouse wheel which...

Would like to have the ability to save the displayed spectrum (just one, not continuous) to a CSV file. Format would be frequency/amplitude pairs. Would also like to have lower FFT resolution (higher resolution BW) settings. Even reducing the...

I would like the application to retain my AGC, Noise Blanker, Noise Reduction and notch settings (basically all settings in left hand pane below the filter settings). When I shut down the program then restart it, the last settings and band I used...

Hi,

i have lot of spectrum record files from v.3, but old v.2 Data Decimator is not compatible with these files. Is in the plan new Data Decimator for v.3?

Thank you

Přemek OK1PZH

This request follows on from the other topic of scheduled recordings.

As already discussed the recording scheduler offer tremendous potential for automating complex tasks.

I've sorted out the problems I had and can correctly import a csv file into...

IN an exchange with a fellow FM Dxer today, talking about the ability to automate the recording of segments of a band, or different bands on a rotating basis, for those e.g. whose SDR span isn't large enough to cover the whole band.

One idea is to...

XIT function for external radios that do not have one. To allow transmit on slightly offset frequency. Needs slider control or similar in SDRC to set the offset amount.

Simon,

Can you consider adding independent step sizes for LW. MW and HF under AM so each could have it's own step size setting?

Thanks!

This may have been asked before but what would it take to port V3 so it will run on Android?

Simon:

It would be very nice to have a button in the 'General' Group of the 'Tools' Tab that would open Simon's World Map (if installed).

I'll be really embarrassed to learn this is already implemented somewhere else in SDRC and I've missed it.

Request Visual Gain for Airspy 1 see in Airspy directory

Hi,

Is it possible to tell the timeline for getting the remote SDR recording playback in V 3 , if this is going to happen ?

I can still fall back to V2 but I notice that with the same Airspy the reception in V3 is better as in V2, so now I am...

In the new version 3.0.25, I note there is a drop down selection for step rates. Wonderful!

I saw another post where someone recommended adding 20 khz to allow tuning repeaters in the VHF/UHF amateur bands in the western USA.

I know in the eastern...

Background: APT Satellite reception and display. SDRC is the best (long ago also had display) as receiver and tracker in one package. In my analog design of receivers, I always followed the discriminator with a Bessel 6 or 8 pole low pass filter at...

When using SAM or ECSS modes, how can I see the actual frequency of the station's carrier? The frequency display in SDR Console now shows the frequency as set by me, but not the real carrier frequency. Thanks!

Would it be possible to have easy or quick access to tuning steps?
They say a picture is worth a 1000 words so,

Hi,

I post here, because I think it'll need a new feature, and I never find how to do, with 3.0.24.
I've two SDR AirSpy R2, and a nice feature 'll be to have the two reveiver working at the same time, in a single session of SDR Console.
a...

Two additional buttons in the markers menu, one that will open the edit window for the marker at currently selected receiver's frequency, and one that will delete it, if there's one there. In case there are multiple markers on a single frequency, it...

Favourites are organised in a two-level hierarchy of folders. The Favourites Organiser is a powerful dialogue for managing the favourites structure, and the main subject of these comments.
As an aside, besides the default set of favourites, we can...

Started SDRC with receiver name/model A , not realising it was B connected. Eerie lack of activity, maybe antenna loose??? Clicked Start , restarted program, blah.

When the penny finally dropped I realised that failure to start shows up as lack of...