It's all about the Software

Hi Simon,

One of my equipment configurations in my shack is running my Airspy connected to a buffered IF tap on my FT890. The FT890 upconverts to a 70.455 MHz. This gives me multiple receivers and the benefit of the waterfall.

Because I upconvert,...

I manage to connect my radio via omnirig and display follows in external radio but RX SDR does not follow the frq of my TX

Hi,

Might just be me, but in using the Radio Frequency box that comes up by pressing Home/Frequency
that allows the setting of Frequency and Span:

Again, it might be me, but it seems that the numbers you enter do not appear, always, where you have...

Hi!

Version 3.1 2365 using Windows 11 Intel 10700k NVidia 3070 has no effect when activating noise filters. This was also in the non-beta version 3.1.
Most other functions except Notch on as the filter bandwith, etc work nicely. I have used it on...

I have not been able to use the video recorder feature and the Start button is 'greyed out'. I've looked in the settings and I assume I don't have to enable it in the options. I am using the latest test version although I've not been able to use it...

Hi Simon,
Hi all,

I use v3.1 beta Build 2346 on my Dell Laptop running Win10, updated recently to functional update 21H1. Now Win10, Version 21H1 (Build 19043.1202).
After a couple of hours of operation SDR Console stops working. This was not...

program starts fine but will not connect to rsp1a,, but if I start another program first ( SDuno, or HDSDR) then go back to program it starts just fine. Does this every time.. Any idea??

Getting to know Simon's Map (latest v1.2).

When I set the option to goto Full Screen on startup - it does that.

However when it does startup it briefly shows the menus and map then expands
so that only the map appears on my Laptop screen. OS is...

Repeatable crash in v3.1 (and prior versions):

I left-click within the left half of the waterfall display to pan to lower frequencies. That works fine until the zero-Hertz spike appears and I left-click to the left of it. Then the SDR Console...

I just loaded the 2365 beta and the RSPduo won't start. It looks like it does, but nothing happens after clicking on the SDR to select it on the radio selection screen. It doesn't crash, just nothing happens.

The previous version 2346 worked fine....

Scrolling through the displayed frequency span the tuning bars disapear. Clicking on the signal tunes the radio to 10MHz WWV.

See attached screen recording.

SDR-C Ver.: 3.1 2320

73,
Hauke (VK5HW)

when I try to change frequency's it just keeps playing the same audio and the only way to change frequency's is to turn of and on the scanner. i use a rtl-sdr

Note: on my laptop it works completely fine so i know the rtl-sdr is good

Trying to run two HermesLite-2 radios at the same time in two instances of SDRC. (One is HermesLite-2 (latest built) and other one is Radioberry+RPi4)

I can run either of them individually but I cannot run them both at the same time. I can run two...

HI Simon, Folks,

I tried to install the RX-888 mkII on my PC, used the dedicated USB Drivers and installed the latest SDR-Console version.
Also followed the USB recommendations....

BUT...after selection RX-888 in the local RX menue it tries to...

Hi Simon,

After editing about 50 FAV entries in a row the FAV ADD, UPDATE and Organizer buttons don't response anymore.
The buttons EXPAND, + and - are still working.

It also takes a very long time before Markers/Config opens.
After stopping the...

v3.1 weird tune and freeze PC
I use SDRPLAY RSP2 v3 api on I7 9900k with C:2TB SSD (+3xHD) and 32GBram, CPU used 5/20% depending on the open RX and activity.

Since installing version v3.1 I have these problems:

1. when I open some receivers from...

Hey there,

either I am too blind to check it out, or it seems that the porgram shows the wrong frequency after I dialed/switched it to look around . I used the numbers on the left, also the black-yellowish slider at the lowest bottom.
I could not...

Hi Simon,

When adding/edit Favourites they are not automaticly added/changed in the FFT (as a marker).
To activate every change one have to go to View, Markers, Marker Config, uncheck Fav and check Fav again. A bit cumbersome that way.

Is it...

Hello Simon,

With V3.1, the stability of the QO-100 Beacon Synchronization seems to be noticeably lower than it has been with V3.0.28. While V3.0.28 (and before) showed a sync stability in the order of 1-2Hz, the stabilization is jumping around by...

If audio pops & clicks are heard it may be necessary to re-enter the setting in Options-Audio-Buffering by changing it and/or restoring it to it's original setting. That seemed to correct a serious case of audio popping that occurred after...

It appears the Waterfall resolution is reset to default rather than that selected in the resolution menu after making changes to Satelllite or Favourite entries.
The example I can give is that I have selected x8 resolution ( Menu : View -...

The console is great and my favorite SDR software. I have a few questions,

Question 1
LimeSDR, set RX Ant=NONE: There are 3 spikes on the spectrum: 415.314MHz, 435.000MHz, and 454.686MHz. It looks like 435.000MHz is like a DC spike. The other two...

Hi simon,

I have a problem with the 3.0.28 console and my FDMS2.

When I change the bandwidth, my audio recording and my signal disappear

I've take 3 screenshot of Adobe audio and Console.

LB : 1.536MHZ = OK
LB : 3.072 MHz = X
LB : 6.144 MHz = X...

Bug report:

When recording a stereo FM station using the video recorder, the recorded audio is mono from the left channel and not stereo. Could this please be fixed?

Thank you so much. Loving the software, so many great features!

Andy618.

So I'm an amateur radio operator and I'm using SDRConsole V3 as my panadapter with direct control over my rigs (works great, thank you!). but when I'm say on 80m, I set the RX 1 audio output to the correct device and set the volume for my setup. But...