It's all about the Software

Hi Simon,

When using the SDR Datafile Editor and configuring output to be between certain times, the edit results are ok. The Finish time in the sequence box is however indicating the end time of the source file(s). See attached screenshot.

73,...

In 3.0.27 and also now in 3.0.28 (your latest build) the waterfall displays either a marker or signal on thye frequency slected.
If I retrieve the frequency from my favourites list no additional items are displyed in the waterfall and squeeze and...

I've been using the USB device server myUTN-2500 ( to connect my remote USB devices over the network, including Icom radios and SDR dongles, without using a dedicated computer.
I tested the R2, which was not recognized by the device server. After...

This bug is only present when noise reduction codec 2 is selected.
200hz audio tone overlays AM demodulation and is audible continually.
Tone also initially present on stronger SAM signals but quickly vanishes.
Also present on Wide-L, WIDE-U,...

Hello,
Since upgrading to version 3.026, I can no longer open Icon Select Radio.
When I open it, the sdr consol window freezes.
It is impossible to do anything. I can no longer select any radio station. Both locally and network... :(
Locally the...

Pointing towards our local broadcast FM mast signals can reach 80dBuV so are at the very limit of the S3 signal handling. Overloading can be mitigated by switching off the software preamp or adding some attenuation. The problem is when recorded...

Hey!

I got a SDRPlay RSPDx and I installed all drivers correctly but now if I wanna add the receiver, this message appears:

The problem is that my installed driver is too new or the SDR Console driver is too old

What can I do to fix this problem?

I recorded a .wav snippet from a playback of a larger recording while in Binaural SAM mode. When I listened to it, it played back in a slow manner. Not delayed, but like the recording was playing in half-speed so the voice came out real deep and...

Hi,

this is a crosspost, it first appeared here (I just joined the forum this morning):

I have found an entry in today's Windows Event Viewer that the SDRServerService.exe has crashed last night.

At that time, I didn't use it, and to be more...

I am using SDR Console with a Hermes Lite 2. Most times I start SDRC the meter bars go to some value and stay there during the entire session. Occasionally SDRC would start and operate correctly. Unfortunately the problem has only grown worse from...

HI....

I start SDR CONSOLE 3.0.27 and i receive this crash screen:

Image:

HookmouseProc?!?
I haven't changed anything since yesterday when it went
I use the SDRPLAY RSP2...

I'm solving by restarting and re-saving or resetting everything, but...

My name is Akira JA1OGZ. The SDR Console is very useful in receiving satellite telemetry. It works fine on other PCs.
It is a symptom that is occurring on the PC I am using now, but within a few minutes after starting up, it will enter Trap as shown...

Data Analyser works perfectly on the 1st analysis of each session. But moving on to a new project results in an image which appears “noisy” and overlaid with hash. In order to get a clear image it’s necessary to close the Analyser window and re-open...

Hi Simon,

If I take a screenshot with the Console (.27 3/24/21) on the second monitor it takes a screenshot of my main monitor. It never did that before.

Barry
WB2ZXJ

Hi

My SDR console has suddenly stopped working with my RTL SDR dongle.

It starts up and I select the dongle, but nothing shows up on the waterfall and no sound comes out the speakers.

And when I close SDR Console it crashes.

My RSP1a works fine...

Hi,
When editing a 46 Gb I/Q file (see I-Q file_editing-#1 ) to extract a 200 kHz wide full lenght portion, the size of resulting file is less than 100Mb and the file covers a few minutes only of the original file (see I-Q file_editing-#2 ).
Did I...

Ignore

Hello,
after update from 3.0.26 to 3.0.27 I always get an error dialogue at startup of SDR Console.
Manual press of Start button in the home menu, starts the device.
Version 3.0.26 could start directly one of my 2 two devices connected per USB.
Both...

I tried to schedule a recording.
I entered all the information, frequency, time, duration, audio format, etc.. But the OK button did not enable. So the schedule could not be saved.

Can you confirm that?

Thanks

When using the Receiver Noise Reduction NR3 my Transmit Audio is distorted. When I change to NR1 all is OK. I didn't think there should be a correlation between the receiver settings and the Transmitter functions.
73, Don

Hello,

Sorry, but I realize that I just posted this in the wrong Forum, and that it should be here, probably.

In the select radio screen, it will not accept the Airpy HF+ Discovery, even though it shows as a choice, and I have the Definitions,...

I'm not sure if this has been reported already and if it is a bug or such kind of oddity.
So far I've seen it on the R2, the RSPDX which I use remotely doesn't show this behavior.
The frequency of the radio (the real frequency, not what is shown by...

Normally the frequency change either via the numerical or the spectrum display is instantaneous and without any delays, but now for the second time in a couple of months this is not the case.
Jumped over to my Linux drive and tested the radio's with...

I was running v3.0.26 before, installed the March 26 v3.0.27 and the RDS clock time or CT is showing an hour ahead on all stations that send it.

My region uses RDBS, 75us, and these are strong local signals with the thumbs up icon, bit correction...

I have noticed a minor issue in the Memory tab, that I don't know if it is actually a bug or if the program works kike that by design.
Since I had to do a clean installation, I exported the Memories and View Markers to XML and CSV.
Then I did the...