It's all about the Software

Is there an operating manual for 3.0.26 or .27? Yes or No?

If not current, what is most recent, please???

Thank you

Jerry AB5R

Hi,

attempting to istall the SDR console V_26 I failed directly afte unpacking th install.exe version.
The SDR Console BugTrap reported the issue by naming a physical address area.
The installation issue appeared on an upgraded Windows10 vario...

Hello,

A very general sort of question.

Have often what I can call a bouncing baseline, generally over most anywhere in the spectrum.

Perhaps +/- 2.5 dBm. Sometime more. Sometimes very steady, but usually not.

What are the possible causes for...

Hello,

Years ago, many, I set up a VB-Audio Virtual cable to feed PCHFDL.

The Console end, I think, should be the input to it.

Played around with all the audio settings, but can't seem to feed PC-HFDL.
Probably missing one setup for it,...

Hi folks,

Any idea as to why recordings are upside down?

De Ei2iP Robbie

Hi,

Not important, but was playing around with the built in digital decoder.
Have the mode set to USB

Tried PSK (all of them) at:
1.838
3.580
7.040
10.141

and RTTY at:
3.590
7.043
10.143

Lots of digits appearing, but all gibberish.

Any...

Greetings,

Trying to set up frequency databases for use with SDR Console 3.0.26 on my Windows 8.1 computer.

When I selected either the AM or FM user list, I receiver the error shown on the right hand side of the attachment.

Sorry for using screen...

Hello,

I would like to use the Adalm Pluto SDR remotely over internet between my two locations. In both sides I have Gb fiber connection, so bandwidth is not a problem.
Unfortunately, I am not able to use Server application, since I will not be...

Hello,

I am very new in using Console V3 with FDM-DUO. Ii is very uncomfortable to transmit with it as I can hear my own audio signal in my headphones connected to my computer (the headphones are used as a receiving output). Hearing my own...

Hello,

Re the Stereo/Binaural AM option:

Where, and under what circumstances, do you folks find it useful to use ?
Caveats ?

Why is it suggested not to use with Headphones ?

Thanks,
Bob

On several PC's and laptops I have SDR Console V3.0.2x running, recently all updated to V3.0.26.
all run on Windows 10 - 64 bit.

RTL-SDR stick with Zadig driver (RTL2832U):

a. i5-6300U / 16GB running stable
b. AMD 8core 8GB running stable (but...

Hi

I use a Hermes Lite and virtual audio cable to transfer audio to a 3rd party applications (WSJT-X).
It would be nice to be able to monitor the audio being transferred for the change in band conditions etc, however i've not found a way to do...

Hi Simon,

I'm curious as to when SDR Console 3.1 LTS will be released. Thanks very much for this wonderful program!
--
73,
Jim W7EED

Hello Community,
Using a R820T Dongle, I started playing with the Console. I had found the step -button in the Mode -square qiet helpful to change the frequency steps for special demands.
Since this morning the step -button is missing and I must go...

I have an RSP1A which I've used with SDRuno. I'm needing to run the WF for as much as 12 hours, either a coarse increment (which is fine as I'm looking to see if the noise level changes) or the ability to scroll back in time ... can Console do this?...

Greetings All

through an unknown event my receivers (most of them) became 'minimized', offering only the options to edit or delete, but not to select/use

what did I do ?

can this feature be toggled off indefinitely ?

Thanks & Best 2021 !

I use SDRC as a panadapter with my FTdx5000 transceiver. Normally, I don't need to see anything other than the main spectrum and waterfall panes, which I think is referred to as the RX window. I keep the RX window set to its smallest available size...

In the V2 version of the waterfall, the lines were hidden by the VFO. They remained only in the spectrum. In the V3 version, the carrier wave remains and is hidden under them. Could it be modified as in V2?

Ok, while writing this post I remembered I should try a different USB port, obviously it fixed the problem after I had written this post. So I decided to upload it anyways as a reminder to try a different port.

Hi there,
I'm having the issue that...

Is there anything worth looking at that would help as a tutorial on I/Q files as generated by SDR Console (and SDR software in general)?

After looking at some sites, I'm clear on the idea that I/Q data consists of complex numbers representing a...

I have 3 SDRPlay radios on the same PC and want to have an instance of SDR Console running each.
I have a Main Identity and two Alternate Identities. I have them configured so that when I launch the first instance of Console, the Select Identity...

Screenshot-2020-12-23-102349.jpeg

Just off to the right of the waterfall is a narrow vertical window where you can adjust the window and leveling for the waterfall. At the top is an auto button. As I change bands I hit the auto button to see the...

Is there a way to remove the 'bias t on/off' button?

I'm using an RSPDX, V3.0.26

Hi, when using the frequency database I select a frequency, and SDR Console tunes to the frequency but the screen that displays the frequency does not change to the new frequency from the database. I attached a short video.

Edit: I have posted a...

The beacon offset is written into a CSV file. The maximum number of lines seems fixed to 10 000.
Can this number be changed by the user or is it fixed in the code?
The offset is written in time intervals varying between about 2 and 20 seconds. Can...