It's all about the Software

Hello, I've just installed .25 over .24. I'm hearing a constant tone at approximately 200Hz while receiving weak signals in the AM mode. It sounds like the same tone that occurs in SAM mode when receiving various amateur radio signals that have...

I have looked all over the SDR-Radio website and I cannot find a download link. Thinking it might be at the end of the request for donations, I went there and made a donation which lead me nowhere. I am pretty sure my unattentive blindness has...

I'm using the latest version of SDR-Console V3, and whenever it is running the screen doesn't turn off after the 30 minute idle time set in Window's Power & sleep settings. If Console isn't running, the screen turns off as expected when the system...

Hi
maybe something i have done?

elad fdm duo..all ok on 3.24
updated to 3.25..

now have no tx power from duo..thats on tune and tx.all modes..DUO does go into tx, just no rf out.tx out levels are set to max.
rolled back to 3.24..still the same.....

When switching agc from slow to medium or fast. Crashes the displays.rx still working but all displays freeze.
Have to restart sdrc to fix.

Always does this..windows 10.

Regards..

Hi Simon,
just installed the .25 Version and have some issues which i can't remember having them with the .24.

Whenever i maximize the console window to monitor 1 or monitor 2 with the little monitor icons in the top right corner, some parts of the...

Hi,

Not at all sure if this is practical, , or even if it's a good idea.

But, and it's likely it is only me, but I spend a lot of effort in
coming up with a good compromise between the RF Gain and the IF Gain (when AGC is Off).

I keep thinking...

Is it possible to have the ‘mode’ - USB, LSB etc. on the quick access toolbar ? I can’t find the ‘buttons/s to add if it is !

Thanks !

Steve Jerome

Hello

A question...
I have an RSP SDRduo here.
I have now configured the console for the QO-100.

Now I want to work again with the SDRduo on shortwave with the appropriate parameters.

How can I do this without changing the settings for the...

I'm trying to calibrate my Nooelec R820T2 SDR & TV Dongle but each time I change the calibration setting +or - SDR Console stops receiving a signal in the waterfall. I have to press stop and then start again to receive a signal. Two screenshots...

When using SAM or ECSS modes, how can I see the actual frequency of the station's carrier? The frequency display in SDR Console now shows the frequency as set by me, but not the real carrier frequency. Thanks!

I'm using 4 VRXs, so I really don't need the signal meter & it's getting in the way of the spectrum peaks. Any way to either move it to another portion of the window or just get rid of it altogether?

Thanks

Bob NO6B

Anybody have any idea why I can only get 300khz bandwidth while connecting to an RT820 via SDR Server V3?

Wondering if such a display is feasible, given a decent antenna array and multi-channel receiver...
Obviously need to tune a specific channel (e.g. a VHF BC frequency).

Please excuse horrible graphic

This very occasionally seems to freeze Console, no crash dump.
RSP1A (but FDM-S2 possibly OK?)
Just upgraded 3.0.15 to 3.0.24.
Seem to recall this from last year too.

Nothing to get excited about, especially with my Win7 and frequent low...

Not sure where this should go - but so long as people will read it and tell me what is going wrong.

I am trying to bypass the manual entry into the Scheduler because what I want to set up would take forever . In am trying to import a csv file...

Just an observation.

My PC faced a battle today when running Console at the same time as watching F1 qualifying on Sky Go.

Turned out to be a bit of a battle. Sky Go won!

Console graphics just stopped updating. Guessing Sky Go uses CUDA and takes...

I have been using SDR Console for some time now. The most recent version I used was v3.0.3 build 1263. I use a RTL-SDR v3 with bias tee active to power an LNA at my antenna. Today the laptop that is running this program rebooted for a Windows 8...

Air Spy Win 7 Windows photo viewer Shows blank console and external radio data only ?? DanHam
Screenshot-2020-09-08-082954.png Screenshot-2020-09-08-082954.png

Hi guys.

I would like to set up sdr-console to feed 4 channels /each to different VAC output/. I am using RSP1A - and that covers up to 10MHz spectrum. The problem is that it's working if I use RTL-SDR with 2MHz visible spectrum, but when I try to...

I run a Dell latitude (i5 8gb) as a server (June 2020 build) to my i7 16gb desktop (July 2020 build) (avoids antenna feeder going across the flat). NESDR Smart and Hamitup. For months this has been fine, but in the last two weeks it crashes within...

I wish to do some side by side comparisons of 2 sdr radios..

Is it possible to run 2 radios at same time with 1 pc?

Perhaps with 2 sdrc running?

I have no idea..( but do not wish to try before asking.)

Thank you ..

Does this all the time..

If i change rx mode quickly ( was hunting interference.) then the big centre spectrum and waterfall freezes..
Tx frequency freezes..
Rx if still works..
Then after a minute or so the software crashes/ freezes big time.

Can...

[Copied here from groups.io, as it wasn't answered there. Link to groups.io thread ]

I have some favourites set up that don't have saved receivers (for signals that are too wide for any of the SDR Console receiver options, just for seeing them on...

Hi Simon,
i am using SDR Console 3.0.24 64Bit on Win10 and HermesLite2 or with RSP1A
The Noise reduction NR3 seems not to work like in 3.0.23.
When i am activating NR3 in 3.0.24 the major noise floor seems not to be reduced. It sounds like the...