It's all about the Software

I just recently started playing with SDRs and I've had a hard time finding the source of this audio distortion in SDRC. I don't have this issue with SDR console. Screenshot-2025-03-17-183002.jpeg I uploaded a recording to yt so you can hear what I'm...

SDR Console version 3.4 build 3569

1，When recording data, the frequency in the file name is inconsistent with the actual frequency. I think it is correct to use the current actual received frequency as the file name. In addition, after changing the...

SDR Console version 3.3 build 3236.
I have a new Adlam Pluto just out of the box last week.
I am having problems with stopping and re-starting the Console.
On startup, Select Radio > Definitions > Search Pluto SDR
produces 3 instances. One with an...

I have not been able to get the LimeRFE to work above 100 MHz with SDRConsole. What I have found is the logic levels on U9 (SW6_V2 & SW6_V3) are not correct at 222 MHz. As such it can not receive or transmit on J3 at 222 MHz. SW6_V2 has to be a 1...

SDRC v3.3

When rapidly changing frequencies, sometimes the external radio frequency does not get updated to match the SDR frequency. It usually tracks even when scrolling rapidly, but 5-10% of the time does not. The fix is simply to change...

hello, i have a problem with sdr, namely when i connected a 3.5-52mhz longwire antenna, there appeared such dashed lines on the waterfall in sdr console v3.3, as if reflections of the broadcast station, rf gain is 29.7db
I have rtl sdr v4 Is there...

The spectrum of a spyserver shows op with a peak carrier on any entered receive frequency and a valley around it.
On certain higher frequencies the whole display starts bouncing up and down.

When using the SDR# client all is fine.

You can try with...

Hello! the first audio is with SDR# , 2 meter band, ham qso, NMF 12 khz...the second is with SDR console without noise reduction, NFM 12 knz...device RTL SDR v3, gain set to 38 for both, same time, same antenna, same PC...where am I going wrong?

Hi. I had installed the 3.4Beta version of the console on my own computer and my intention was to use it as a PAN adapter together with a Yaesu FTdx5000 radio. My SDR receiver is a FunCube pro+. The signal is controlled from the IF connector of the...

Hi Guys, I am new here and to the SDR hobby but, I am a long time Radio Ham, G0EMJ.

The problem is that I have 2 SDR units, RTL-SDR and Nooelec NESDR SMART but, neither one of them will pick up a station on 105.4 mhz FM.
This is a station I listen...

I have Omni-Rig v2.0 installed and running and am able to connect to SDRUno just fine and control my radio (FT-991A). I have installed SDR Console (v3.3) and even the Beta (3.4) and am unable to connect to my external radio because it constantly...

Hello all....

I was on QO100 calling CQ whit my voice keyer running, after som call a other ham told me that I was to wide, arround 3.5khz++

I have my settings on 3Khz BW in sdr-console 3.3, so I am a littel confused about that I have so big BW...

I have a user that probably doesn't know that one can use the pre-amp even with the AGC on.
It might be too late to train this person that you don't have to turn off the AGC to get a preamp on
for use when on 20m and higher.

I am forever finding...

Hi, new on this forum.
I use HL2 with all softwares like Thetis Sparksdr and Quisk, but with SDR console V3.2 or 3.3 the output power is around 0.5 W when speaking in the mic ( drive , proc & gain 100%) - Tune or whistle gives around 4 W a little...

Greetings all,

I basically reimaged my system, finally, after I can't even begin to ponder how long. So a new SSD a new install, a new experience right? All goes well, at least I thought so until I go to install my favorite SDR app. It doesn't...

i attempted to connect to an ANAN-10E which has already been verified using linHPSDR. Result: Nothing found, sorry!

however, in the logfile, there appears a response when i lied to SDRC 3.0.26 and told it to look for a Hermes Lite.

Note the...

Hello to the group,

In transmit mode, no data ( power - swr - drv - vdd) except ALC in the transmit meter display.
Screenshot-2024-08-22-111012.jpeg

Thanks for reading !

Renauld ON4KVI

Hello, I have been experiencing this bug for a while but recently noticed that I can easily recreate it just by quickly switching back and forth between receivers. Here is what happens:

1. Create two or more virtual receivers (i usually have 3...

Hello!
I am looking for help, explanation, ideas for my situation..
I'm a SDR Console user from ver 3.0.26 (2020-12-14) and now I'm @ ver 3.3 build 3236 from (2024-02-05)

Strange things started a month ago - the program did not start (the frequency...

Using SDR Console version v3.3 build 3195.
Context:
Using favourites with multiple receivers where each receiver has a different audio device.
All these audio devices are VAC's and feed different decoders.

When I add a new receiver, select its...

I have 3 ADALM Pluto sdr's all set up using IP addresses. It does not matter which one I select, it only uses the first one in the list.

I see we can create 8 receivers but only have FA-FF (6) commands for set/get frequency. Can we get FG and FH added?

Helllo, recently tried out the MIDI functionality which is really nice. Thanks for that. I have found that if I make a slider for volume control that has a range of 0 to 127, the software detects it properly and sets the values in the midi config...

When I try to connect to bladeRF v2 in SDR console please wait appear and then I see crush report.

crash report:

SDR Console has been working flawlessly until today when a Windows update installed. Now SDR Console will run only a minute or two then freezes, accompanied by the disconnect sound ding. I can click on the stop button, wait a minute or so, then...