It's all about the Software

Hi all
I have set up a server. When I log in to the server to listen, it may be a problem with the network speed. The waterfall chart often stops and then resumes in an instant, and the audio is the same. I have set the bandwidth to 30K. The...

Hello:

Perhaps it is just me, but I am having trouble figuring out how to keep the freq span in the display after zooming in. The default seems to be 0-100 khz. I've tried all kinds of things to keep the span coming up every time I go to that band,...

Hi All,
maybe I am doing something wrong but the tuner is not stored when I create Favourites?
I setup and stored Tuner A for 367.080MHz that is connected to my PTRX-9700 for 1296Mhz and via MAP65 setup to QMAP/MAP65
I setup and stored Tuner B for...

Hi all,

I'm one of those intuitive techy autistic types.

I want to use SDR Console with Omnirig and Soundcard from IF / IQ on the Xeigu I use in my portable setup.

HDSDR is OK ...I have it setup perfectly, but Console looks great!

Would like...

Sorry if I might have gotten this wrong,
But I had the impression that console could be used to do soundcard I/Q Conversion and could do bi directional sync with Omnirig ..

Yet I am stuck on radio definitions ...

It seems I'm mistaken?

Hi! Is it possible with SDR Console 3.3. to scan a range of frequency from....to....? Thank you

I have a good signal on my FM station, but I am experiencing hissing noise in the background.

Is there anyway I can remove the noise. I have tried the noise filters, but it doesn't seem to make any difference.

Thanks in advance for your help.

OK, spent some time this AM doing A/B tests using the Nooelect Flamingo AM BC Filter.
The setup is:
Inverted L antenna, active 4 port multicoupler, two Airspy units with same firmware, two copies of SDRC running side by side. The copy on the left...

Does SDRConsole allow for Trunked signals or if not compatible with plugins like SDRTrunk or DSC+?

Hi. New user to SDR Console, but liking what i'm seeing thus far. That said, i've run into a very odd behavior using SDR Console 3.3 on a Windows 10 laptop with my Afedri-LAN (connected via ethernet). For the life of me, I cannot get intelligible...

In an effort to keep a daytime, 5KW AM radio station on 1540kHz 5.1miles (8.2km) away from me appearing in numerous locations in the upper bands, I thought I would give the Nooelec Flamingo AM BC filter a try. Thinking all my SDR's at three entirely...

Sorry if this has been raised before.
I have a hard drive folder containing one set of chained recordings made by SDRC. They were found in an internet archive of HamSCI files.

The first 30 or so had been omitted, so the filename sequence begins...

While investigating the QRM generated by a local AM BC station that jumps to 5KW at local sunrise, I found the following action with the Radio Airspy Discovery using my
normal settings of:
AGC High (or low) doesn't matter
Attenuator OFF
Pre Amp OFF...

I'm new to using SDR radio / software. I recently purchased a HF+ Discovery, and running it with SDR Console (SDRC) v3.3 I recently downloaded.  It's working great, but how do I know if I'm leveraging the proprietary noise reduction algorithm...

I think there is a problem with applying a frequency calibration correction with the SDR receiver (a Zyncsdr / Libresdr) listening to the 70cm band (433.5 to 434 MHz) while the signal comes from a QO100 downconverter running between 10489.500 MHz...

Is there more information about MAP65 Support in newer SDRConsole beside of whats in the SDRConsole itself

To be able to use SDRConsole with MAP65 for X-Pol (H/V) antennas it need support of two coherent 96KHz I/Q streams coming from a Dual...

I would like to use sdr-console to tune into narrowband signals acquired by a Casper SNAP board.

So I'm looking for documentation on a suitable IQ data stream that sdr-console recognizes. The SNAP is set up to easily stream UDP, so I'm looking for...

Subject: Assistance with Ingesting Raw IQ Data from SDR Console across LAN into Python on another PC

Hi, I’m attempting to ingest raw IQ data output from either the Data Repeater or the SDR Server in SDR Console using Python. I can successfully...

Hi all,
I have a RTL-SDR V4 and trying to use it with SDR Console V3 on a Win 11 laptop.
I've spent time familiarizing myself with the software and now trying to listen to incoming signals.

The problem is that the sound is terrible. It sounds like...

I would like to transfer the matrix setup I have configured on one computer to another computer also running SDR-Console. The matrix is pretty tedious to set up, but I can always call up the configuration on each computer and manually transfer the...

hi, regarding NFM listening both of communications in general and communications in amateur radio bands (e.g. in the 2 meter band) what configurations do you use as filter width and above all as noise reduction? I am using for the 2 meter band a...

Is it possible for SDRC to control (send band data) an external BPF like the OM-Poer OM6BPF ?

Is there an ADC overload indicator in SDRC ?

New user as of today. Where do I go in v3.3 to change the audio output from default (speakers) to another destination? Also, is there a virtual cable that works well for connecting SDR Console to WSJT-x?
Many thanks for any responses!
Keith - ke4th

I have an odd question which may be quibbling but is more likely just me having an improper setting somewhere.

I am using the DX Cluster window, with spots on display above the waterfall. Now, ujsually when I go to a band in the default favourites...